I've been having troubles with my 37 clutch for some time now. As per some previous posts, the battle has gone from linkage issues to include fork alignment and the connections thereof to pressure plate issues to throwout bearing issues. I've pulled everything apart a number of times. Replaced the pressure plate, the clutch the throwout and most everything else in one respect or the other. I did everything EXCEPT swap flywheels to the next model and changed everything... and then I even (and finally) did that.
So here I am with a truly NOS 1938 upgraded flywheel, pressure plate and clutch. It was hard to find anything that wasn't worn out but I finally light on a 4 bolt flywheel to fit my crank but with the heavy 9 bolt pressure plate version which was made for the heavier trucks of the era. I found the appropriate pressure plate and the 10 3/4" clutch all of the same heavy truck vintage. I already had a brand new throwout bearing from a previous unused set so with everything in hand, I proceeded to bolt it all together.
I didn't fully explain what brought me to this though. As mentioned earlier, I could never get any of the 37 clutch flywheel pressure plate combinations to work without some level of vibration that wasn't there when I bought the car. I won't go into all the details but if it wasn't the pedal shaking, it was the whole engine. I've read how the 37 pressure plate was a bi*ch to get all right but d*mn. I finally gave up, replaced everything with 38 and checked for vibration every step of the way. All good.
So anyway, I now have the 38 truck setup. Everything seems to fit. The newer pressure plate has the bladed fingers instead of the three finger (impossible to adjust) setup that the 37 had. The clutch is wider and has more surface area. I had the flywheel checked for balance and it was spot on. I poked around and even found a pristine NOS clutch fork for the 38 version throwout. I also checked the bearing for the same size inner diameter as the 37 to match the trans input shaft. All is right with the world. OK... in my little world at least.
I'm now at the pedal adjust phase where I want to have a clean non-rattle pedal and as such, a throwout bearing that doesn't wobble on the input shaft of the trans when it's free of the pressure plate teeth. On newer vehicles there is a sleeve that the bearing slides on so to keep it from bouncing around. On the early setups (unless that's the part that was lost years ago) there is no sleeve so the bearing has nothing to keep it from shaking against the shaft. That is unless I adjust it to barely touch the blades at all times. Everything I've read though says that this is a bad thing but everything else I've done says THATS the only way it'll stay smooth.
So that's my dilemma. Touch all the time and stay smooth... or give it the free play the books recommend and the whole assembly rattles. Oh, and if I don't snug the bearing to the blades, I don't get enough travel to fully disengage the clutch and it grinds when it goes into gear.
Final note: the 38 fork teeth do not set centered on the throwout bearing sleeve. It hits a little like the fork to pivot length is just a little too long. But I've looked everywhere I can find and there is no mention of a different fork length (pivot point to fork teeth) for the heavy truck config. There IS mention at the pedal end being a little different to fit the truck surroundings but nothing at the bearing end. The only difference is the different 9 bolt pressure plate config and the more robust clutch diameter.
@skidplate The sleeve you mention is the transmission front bearing retainer. The correct one for the 1938 and later clutch setup, has the sleeve for keeping the throwout bearing in its proper location. You will need to have the correct retainer before you can expect proper operation of your clutch. Your fork length issue could be because the truck clutch housing is different from the car housing. The car housing is different from 1937 to 1938. The Master Parts Catalog says you need a 1938-1947 truck clutch housing to match your other parts. I don't know what is different about the truck housing but I suspect that location of the fork pivot ball could be at least one of the differences. You pedal stroke issues might be solved by proper location of the fork. Since truck transmissions are longer that car transmissions, during this period, there could also be some compensation for this in the depth of the housing. Bolt pattern for the transmission might be an issue, as well. I have some random 216 clutch housings laying around and I would be happy to do some measuring, if that would be helpful.
I'm sorry that you had such bad luck with your original carbon throwout bearing setup. There are often chatter issues, but I have never had problems bad enough to make me want to change out the entire setup. My 1935 car and 1936 1-1/2 ton truck are both still using their original style parts.
Let me know if I can help.
Mike
Many Miles of Happy Motoring
3469 Posts on Old VCCA Chat
Here's a comment from Lou MacMillan. He's having PC issues, so he can't post stuff right now.
" The 1938 bell housing can be bolted to a 37 block.
It allows the upgrade to throw out bearing from a bushing
and a positive engagement starter from a bendix spring. "
Hope this helps.
Dean
Dean "Rustoholic" Meltz
San Leandro, CA
3511 posts on vccachat.org
Lurch -1927 LM one ton truck - tinyurl.com/Lurch-VCCACHAT-Gallery
Justin - 1928 AB Canopy Express (1/2 ton truck) - tinyurl.com/Justin-Stovebolt-Gallery
@rustoholic @skidplate I forgot to mention in my previous post that the 1938 starter is different from 1937. I think you will need to add that to your list of changes.
Mike
Many Miles of Happy Motoring
3469 Posts on Old VCCA Chat
Yea well I'm getting pretty good at taking it apart, changing something, then putting it all back together. This'll be the forth time I think. I DID have to relabel my gear oil bottle though to "Just a little used".
Im also on version 6 of my rear shock brackets. I replaced the knee action for tube. It's amazing what one can do with some heavy angle iron and a three axis mill.

