Recent Posts

Page 1 / 6 Next

	Topic Title	Forum
	Plasti-gauge use By Tiny 11 hours ago \| Last Post: 6 hours ago	Technical - General
	I have been rebuilding thick babbit bearing engine... 6 hours ago By Chip First, I have not yet read the G&D article. ... 7 hours ago By Stovb... I found this AI post and it pretty well sums up my... 9 hours ago By Steve...
	1947 Chevy Radio Fuse By Clarence W Forsythe 4 days ago \| Last Post: 1 day ago	General Discussion
	According to my paper work , a 14 amp fuse. 1 day ago By Russe... Can anyone tell me the fuse number for a 1947 Chev... 4 days ago By Clare...
	1933 Chevy Coupe questions By K-D 5 days ago \| Last Post: 2 days ago	General Discussion
	Hello Mike and thank you. Yes, the federal agency ... 2 days ago By K-D @k-d-2 Kathleen, A couple of things come to mind. ... 2 days ago By 35mik... I am new to this forum and not at all knowledgeabl... 5 days ago By K-D
	Tight Motor 50 216. By 64672 2 days ago \| Last Post: 2 days ago	Technical - Mechanical
	Ditch the plasti gauge and use the method in the m... 2 days ago By Tiny I found my rod and main bearings were loose becaus... 2 days ago By 64672
	1929 Chevrolet AC carburetor issue By paul baresel 4 days ago \| Last Post: 3 days ago	Technical - 1929-1932
	The idle adjustment screw adjusts the dilution air... 3 days ago By Chip Thank you for your help on pin location. In the ... 3 days ago By paul ... @chip Hi Chip Am I remembering right that the... 4 days ago By Stovb... view all posts
	Chat user contact By Steve Dalphonse 7 days ago \| Last Post: 3 days ago	Forum and Website Usage Questions
	Thanks Tiny! I had misread that initial. I just no... 3 days ago By Nick ... This is the email shown in his club profile: howar... 3 days ago By Tiny Tiny, I tried to send a carefully crafted email ... 4 days ago By Nick ... view all posts
	Compression test reveals and unexpected issue By Stovebolt 6 6 days ago \| Last Post: 4 days ago	Technical - 1929-1932
	I have not used a neoprene or similar gasket for y... 4 days ago By Chip @stovebolt-6 Go down to your local auto parts stor... 6 days ago By 35mik... Thanks Ole! I made a new gasket and the pump wor... 6 days ago By Stove... view all posts
	Repolarizing the generator when using a battery disconnect switch By Michael Tobin 2 weeks ago \| Last Post: 4 days ago	Technical - Electrical - 6 Volt
	Taking the negative battery cable from the post is... 4 days ago By Chip @lee I don't think anyone is disputing the wisdom ... 6 days ago By Tiny My recollection is a bit vague, but I recall the r... 6 days ago By 37Blu... view all posts
	1928 Pressure plate By Bob Wickham 1 week ago \| Last Post: 6 days ago	Technical - Mechanical
	@ole-olson thanks Ole. It looks okay so I think I’... 6 days ago By Bob W... @rustoholic thanks Dean. I don’t think I need to d... 6 days ago By Bob W... Hi Bob If it's not cracked, warped, or badly sco... 1 week ago By Stovb... view all posts
	Electrical & coolant issues By Ken Albers 2 weeks ago \| Last Post: 6 days ago	Technical - 1933-1936
	I thought I sent this, but my computer says someth... 6 days ago By Ken A... @bowtiefan Are you sure the generator is even t... 1 week ago By Stovb... Stovblt, I did that, and nothing changed. Still d... 1 week ago By Ken A... view all posts