Recent Posts

Page 2 / 6 Prev Next

	Topic Title	Forum
	Tight Motor 50 216. By 64672 6 days ago \| Last Post: 6 days ago	Technical - Mechanical
	Ditch the plasti gauge and use the method in the m... 6 days ago By Tiny I found my rod and main bearings were loose becaus... 6 days ago By 64672
	1929 Chevrolet AC carburetor issue By paul baresel 1 week ago \| Last Post: 1 week ago	Technical - 1929-1932
	The idle adjustment screw adjusts the dilution air... 1 week ago By Chip Thank you for your help on pin location. In the ... 1 week ago By paul ... @chip Hi Chip Am I remembering right that the... 1 week ago By Stovb... view all posts
	Chat user contact By Steve Dalphonse 2 weeks ago \| Last Post: 1 week ago	Forum and Website Usage Questions
	Thanks Tiny! I had misread that initial. I just no... 1 week ago By Nick ... This is the email shown in his club profile: howar... 1 week ago By Tiny Tiny, I tried to send a carefully crafted email ... 1 week ago By Nick ... view all posts
	Compression test reveals and unexpected issue By Stovebolt 6 1 week ago \| Last Post: 1 week ago	Technical - 1929-1932
	I have not used a neoprene or similar gasket for y... 1 week ago By Chip @stovebolt-6 Go down to your local auto parts stor... 1 week ago By 35mik... Thanks Ole! I made a new gasket and the pump wor... 1 week ago By Stove... view all posts
	Repolarizing the generator when using a battery disconnect switch By Michael Tobin 3 weeks ago \| Last Post: 1 week ago	Technical - Electrical - 6 Volt
	Taking the negative battery cable from the post is... 1 week ago By Chip @lee I don't think anyone is disputing the wisdom ... 1 week ago By Tiny My recollection is a bit vague, but I recall the r... 1 week ago By 37Blu... view all posts
	1928 Pressure plate By Bob Wickham 2 weeks ago \| Last Post: 1 week ago	Technical - Mechanical
	@ole-olson thanks Ole. It looks okay so I think I’... 1 week ago By Bob W... @rustoholic thanks Dean. I don’t think I need to d... 1 week ago By Bob W... Hi Bob If it's not cracked, warped, or badly sco... 2 weeks ago By Stovb... view all posts
	33 Master Frame Number By Jon Tagge 2 weeks ago \| Last Post: 2 weeks ago	Technical - 1933-1936
	@michael-falise Thanks. It's on the right side on ... 2 weeks ago By Jon T... Not a 33 but on a 34 Master. Stencil is on the pas... 2 weeks ago By Minet... @chip Thanks, that's what I thought. When I have t... 2 weeks ago By Jon T... view all posts
	51 Powerglide leak By David Jewett 2 weeks ago \| Last Post: 2 weeks ago	Technical - Mechanical
	I have transmission fluid leaking at the bottom of... 2 weeks ago By David...
	1933 Cooling Issues By Gene Kruger 2 weeks ago \| Last Post: 2 weeks ago	Technical - 1933-1936
	If coolant out the overflow is the issue, are you ... 2 weeks ago By Tiny I went on a week long early six rally where the te... 2 weeks ago By Gene ... @gene-kruger Gene, I split your question off into ... 2 weeks ago By Tiny
	35 Serial Numbers By Jon Tagge 2 weeks ago \| Last Post: 2 weeks ago	Technical - 1933-1936
	@35mike Thanks. I'm not good at Math or numbers. T... 2 weeks ago By Jon T... @jon-tagge Jon, Perhaps I should revisit the math ... 2 weeks ago By 35mik... @35mike Wow, that's different from the number I ha... 2 weeks ago By Jon T... view all posts