Hand Brake Lever Spring on a 28, correct position

You are not logged in. [Log In] VCCA Homepage » Forums » Chevrolet 1912-1942 (Pre-War) » 1912-1928 » Hand Brake Lever Spring on a 28, correct position

Today's Birthdays

None of any significance today.

Featured Chat Guy (or Gal)

Charlie

Registered: 04/04/02
Posts: 2

VCCA Member's Photos

Member's Projects

Top Posters (over the past 30 Days)

Topic Options

Rate This Topic

#181458 - 08/23/10 01:12 AM Hand Brake Lever Spring on a 28, correct position
1928isgreat Registered: 04/21/10 Posts: 934 Loc: Melbourne, Victoria, Australia	Hi Guys, Excuse me if this sounds dumb, but I am trying to fit the correct spring in the hand brake lever. Up until now have always had a improvised one that just failed. Any chance some one could send me a picture of how it looks fitted, with a bit of a run down on fitting as I am not sure how it fits. Just goes to show there are still things to be learned, even after 30 odd years. Regards Ray _________________________ Some say "Street is neat". I prefer "1928 is great" I have documented my 38 years with a 1928 Chev Tourer, from 1973 to 2012. The highs, the lows, the good and the bad. Let me know what you think of it. Your comments are most welcome.Can be viewed at http://my28chev.blogspot.com/
Top

The Filling Station 1912-28

#181459 - 08/23/10 02:15 AM Re: Hand Brake Lever Spring on a 28, correct position [Re: 1928isgreat]
jack39rdstr Registered: 07/24/05 Posts: 1418 Loc: Sydney, Australia	The www.fillingstation.com list a spring for 1929 onwards, part number FS-136 I have a parts book which lists part number 590303, spring brake lever pawl rod grip , cap,nat, int, uni, ind. _________________________ Jack
Top

#181460 - 08/23/10 03:05 AM Re: Hand Brake Lever Spring on a 28, correct position [Re: 1928isgreat]
1928isgreat Registered: 04/21/10 Posts: 934 Loc: Melbourne, Victoria, Australia	Hi Jack, I have the correct spring, just not sure on the correct fitting. Regards Ray _________________________ Some say "Street is neat". I prefer "1928 is great" I have documented my 38 years with a 1928 Chev Tourer, from 1973 to 2012. The highs, the lows, the good and the bad. Let me know what you think of it. Your comments are most welcome.Can be viewed at http://my28chev.blogspot.com/
Top

#181461 - 08/23/10 03:34 AM Re: Hand Brake Lever Spring on a 28, correct position [Re: 1928isgreat]
jack39rdstr Registered: 07/24/05 Posts: 1418 Loc: Sydney, Australia	On the (1931 & 1932) hand brake lever, the long side of the spring tucks in under the release handle, about 2 1/2" long, and the other end of the spring slips into a hole right at the bend in the main handle, on the AFT side ,about half inch up from the pivot hole for the release handle. _________________________ Jack
Top

#181467 - 08/23/10 05:57 AM Re: Hand Brake Lever Spring on a 28, correct position [Re: jack39rdstr]
1928isgreat Registered: 04/21/10 Posts: 934 Loc: Melbourne, Victoria, Australia	Thanks Jack, Got it, for some silly reason I was completely trying to fit it a different way. Regards Ray _________________________ Some say "Street is neat". I prefer "1928 is great" I have documented my 38 years with a 1928 Chev Tourer, from 1973 to 2012. The highs, the lows, the good and the bad. Let me know what you think of it. Your comments are most welcome.Can be viewed at http://my28chev.blogspot.com/
Top

Hop to:

Your Status

Please login to post or reply.* * *
Send My Password

We speak Chevy!

12/16/2001