|
|
|
1912-1928
|
|
Hi Grant, Gez, I did not know Chev Tubes were that big??? Cheers Ray
|
|
PARTS - For Sale
|
|
Vintage "Passing " light--Restored -------------------------------------------------------------------------------- Location: Wellington , Ohio Price: IN AD 1930'S/40's Auxiliary " Passing " light and bracket This light
|
|
PARTS - For Sale
|
|
-------------------------------------------------------------------------------- Location: Wellington , Ohio Price: IN AD 1930-48 Oil Company road maps 1930 Mobil Oil map of Pennsylvania.Very good condition, Would be nice framed and displayed.
|
|
PARTS - For Sale
|
|
Vintage Accessory Switches -------------------------------------------------------------------------------- Location: Wellington, Ohio Price: IN AD Vintage Aceessory Switches On/off , push/ pull switches with vintage plastic knobs. Come with
|
|
PARTS - For Sale
|
|
1962 Ohio license plate pair -------------------------------------------------------------------------------- Location: Wellington , Ohio Price: IN AD These are in nice cond , good enough to install as is. Price is $18.00 for pair , plus shi
|
|
PARTS - For Sale
|
|
1960 Ohio license Plate pair -------------------------------------------------------------------------------- Location: Wellington, Ohio Price: IN AD See photo for condition , straight , no holes. Price is $18.00 for pair plus shipping check
|
|
PARTS - For Sale
|
|
1949 Ohio license plate pair -------------------------------------------------------------------------------- Location: Wellington , Ohio Price: IN AD Very good condition Alluminum plates. Price is $35.00 plus shipping Check , USPMO, paypal
|
|
PARTS - For Sale
|
|
Vintage door mirror / Rectangle Head -------------------------------------------------------------------------------- Location: Wellington , Ohio Price: IN AD Vintage door mirror /Rectangle head Very nice near new mirror. Possibly never mou
|
|
PARTS - Wanted
|
|
Found a supplier for those. They are called Northfield Forming, http://northfield-forming.com/ . They'll do them as you need them. They also do running board moldings and such.
|
|
1912-1928
|
|
Thanks for the reply Chipper, Yep this one is still holding air well... I think it will make an appearance in our swimming pool next summer its just big enough for my bum by the look of it
|
|
Mechanical - Engine, Trans, etc
|
|
Just picked up the ignition parts suggested by P.U.Guy in the 6 volt forum. One of these days it should run out of reasons not to start.
|
|
PARTS - For Sale
|
|
Chevrolet Wheels. 5 each 16 inch 6 lug pattern 8 spoke style that are correct for 1937 and 1938. Good straight condition. $20 each or all 5 for $75. Call Jay Glass (former VCCA member) at 303-221-0777
|
|
PARTS - Wanted
|
|
Correction. After looking in the Master Parts Book, I need a 30-31 Low-Reverse gear for a 6 spline shaft. Cleon
|
|
Mechanical - Engine, Trans, etc
|
|
Charlie, here you go again, always learning new things. The drill needs to turn clockwise...that is clockwise! You probably have the engine ok if you brought oil up to the rocker arms, now you need to get the oil pump and distributor in sync a
|
|
1937-42
|
|
If it is anything like the 38, the difference between ID and OD is not that great and that in itself would make replacement with the shaft in place, difficult.
|
|
1912-1928
|
|
My 28 Chevy has what the PO called an "Optional Harvey bumpers". The bumpers are very unique.I googled "Harvey Bumper" and found nothing. Ever heard of them?If you would like to see a picture,email me @ fsb1@att.net
|
|
1937-42
|
|
Hi again The seal is metal encased, the original one was cork, and the one I got with the rebuild kit is metal cased rubber. If you pull the pitman arm, which you will have to do in order to get at the seal,you will be able to see the edge of the met
|
|
PARTS - Wanted
|
|
I need a low-reverse gear for a '29 to 31 passenger 3 speed transmisson. Mine is short a tooth. Cleon
|
|
PARTS - Wanted
|
|
Sorry Gene. I didnt know they were different. I'm not familiar with 36 stuff. Do you have pictures of them both? If so you can send them to dallas.miles@live.com Thank you
|
|
Mechanical - Engine, Trans, etc
|
|
P.K. If the hoses you have don't match up try O'Riely's. I got the exact match from them and now have no leaks when I fill up. Good luck, Charlie
|
|
Mechanical - Engine, Trans, etc
|
|
Chipper, Dang! I would have thought counter clockwise. I learn something new all the time here on chatter. Tell me, though, If a rebuild has been properly assembled, i.e., lubricated at rub points, bearings, etc, and given the immediate response o
|
|
General Discussions
|
|
I always add some MMO at every oil change...I love that stuff.Good for the Valves......ED
|
|
1955-57
|
|
From what I have ever seen all station wagon bodies were made at the Cleveland Fisher body plant.
|
|
1937-42
|
|
Easy there, Mate! I know where Australia is. Do too! And, I know how to chunk a mean boomerang. I been practising and now have the art so sophisticated, diciplined and mastered that when that sucker comes back to me it just hovers for a spell
|
|
1937-42
|
|
I would still recomend 85/140 as the 85 will result in good flow when cold and the 140 will be "thicker" when hot which will help to fill in the gaps that were built into these older rear ends. I would not use straight 140 and I would not a
|
12/16/2001
